HDMI HDBaseT Balun Pair with IR/RS232
40-2010 - HDBaseT v2.0 HDMI 4K x 2K \ 60hz POC Standard Balun over Single CAT5e/6 Cable. The 40-2010 HDBaseT v2.0 balun provides a single UTP category 5e/6 cable solution to deliver pristine digital signals from all HDTV formats and signal sources from 480i/p to1080i/p, 4K x 2K \ 60hz. Provides bi-directional IR and RS232 support with POC to the receiver for a single cable solution. Option 1, 3rd party IR interface control and connectivity. Option 2, stand alone IR receiver and emitter solution. Send IR control signals from any 3rd party automation systems bi-directionaly using Calrad_s optional 40-IRC3 interface cable see Option 1 IR connectivity below. L.E.D. indicators provide reference for Power, HDMI signal status, HDBaseT UTP cable signal reference. See Typical Hookup, Diagram 1A below for connectivity details.
Please Note! the following information when using this product Signal transmission distances may vary and are dependent on manufactures individual HDMI specifications and the quality and type of UTP cable used. All products should be fully tested prior to committing to a UTP Cat5e, Cat6 solution and running long runs of cables inside walls, possibly compromising your installation. All UTP wiring and RJ45 connectivity start to finish should be certified to 568A or 568B standards and tested before connecting the Transmitter to the Receiver.
Warning!!!Since HDBaseT standards use (POH and POC) power connectivity, damage may result to both the Transmitter and Receiver if inconsistent or improper wring are used and standard UTP wiring and termination is not followed from start to finish. Failure to follow proper connectivity will void the warranty on this product. For further technical assistance or questions regarding connectivity and termination or for IR control related configurations or IR specific questions, please contact our technical support department.
Specifications:
Please Note! the following information when using this product Signal transmission distances may vary and are dependent on manufactures individual HDMI specifications and the quality and type of UTP cable used. All products should be fully tested prior to committing to a UTP Cat5e, Cat6 solution and running long runs of cables inside walls, possibly compromising your installation. All UTP wiring and RJ45 connectivity start to finish should be certified to 568A or 568B standards and tested before connecting the Transmitter to the Receiver.
Warning!!!Since HDBaseT standards use (POH and POC) power connectivity, damage may result to both the Transmitter and Receiver if inconsistent or improper wring are used and standard UTP wiring and termination is not followed from start to finish. Failure to follow proper connectivity will void the warranty on this product. For further technical assistance or questions regarding connectivity and termination or for IR control related configurations or IR specific questions, please contact our technical support department.
Specifications:
- HDTV Resolutions: 480i/p, 720p, 1080i/p @ 24/50/60Hz, CAT5e 70M (229Ft.)@1080i, CAT6 45M
- HDCP Support: V1.4, V2.2, _ YUV: 4:2:0
- UTP Cable Distance: CAT6 70M (229Ft.) at up to1080p CAT6 40M (130Ft.) at 4K x 2K
- Audio Support: LPCM 7.1, DTS Digital, Dolby Digital, DTS-HD and Dolby True HD
- IR Carrier Frequency: 30Khz ~ 60Khz (Non-Flashing Emitter works with IR-UV STB)
- IR Input/Output Connectors: 2 x 3.5mm Mono Jacks each unit, IR In/Out
- RS232 Protocol: Supports Bi-Directional Transmission, 2400-115200 Baud
- RS232 Input/Output jacks: 1 x 3 position Phoenix Terminal Jack per unit with mating male solderless 3 position screw terminal plug
- Operation Mode Switch: For bypassing RS232 or Firmware Updating
- HDMI ln/Out Connectors: 19 pin Female Jack, 1 x RJ45 Shielded Jack each unit
- IR Receiver IR Emitter Cable Length_s: 3 ft.
- Power Input: Transmitter side only
- POE: POC Standard, power from TX to RX over Cat5e/6 cable
- DC Power Supply: 1 x 12V, 2Amp Regulated
- Color: Black
- Weight: 349g each unit
- Dimensions (Transmitter, Receiver): 4.13" L x 2.80" W x 0.98" H
- Mounting: Transmitter, Receiver 4 x Mounting Holes